TLE
major
A low voltage
power supply converts ________.
a. AC voltage
output
b. Pulsating DC voltage
c. DC output
voltage
d. AC and DC
voltage outputs
When checking
an open resistor using an ohmmeter the resistance reads ________.
a. zero level
b. high
resistance but within the tolerance
c. infinite
d. low but not
zero
Moving one
plate of a capacitor further away from the other will ________.
a. decrease capacitance
b. increase
capacitance
c. decrease
voltage rating
d. increase
mutual transductunce
What is the
reason why threads become stripped?
a. screws are over tightened
b. screws are
heated
c. screws are
molded
d. screws are
painted
What does VOM
mean?
a. AC Voltmeter
b. Ohmmeter
c. DC
Milliammeter
d. Volt-Ohm-Milliammeter
Which tool is
used to cut the insulation without cutting the wire?
a. utility knife
b. hacksaw
c. side cutter
d. wire stripper
What does LED
stands for?
a. Light
emitting display
b. Low energy
display
c. Light emitting diode
d. Light
emitting detector
Which picture
or sketch shows the components of a circuit and how these components are
connected together?
a. Wiring
diagram
b. Block diagram
c. Pictorial diagram
d. Schematic
diagram
3 pieces of
resistors in which the values are 10 ohm, 20 ohms, and 50 ohms. If the 20 ohms
is open, what will be the reading in the ohmmeter?
a. 60 ohms
b. 0
c. infinite
d. 80 ohms
Why does an
AM receiver receive or pick-up signal despite the far distance from the
transmitter compared to the FM receiver?
a. The AM
receiver picks up signal easily because of the transistor.
b. The AM
receiver picks up signal easily because the signals transmitted by the AM
transmitter is by means of line to sight.
c. The AM receiver picks up signal easily because the signals
transmitted by the AM transmitter is by means of line to ground.
d. The AM
receiver picks up signal easily because the signals transmitted by the AM
transmitter is by means of line to televise.
The recommended height of lettering for
subtitles is ___ of an inch.
A. 1/16
B. 1/8
C. 3/16
D. ¼
Which of the following combinations of
letter can be overlapped slightly ?
A. D,E
B. L,T
C. M, N
D. A. B
The following are descriptions of tangent
lines except___.
A. A straight line is tangent to a circle
when it touch at only one point
B. The radius of a circle drawn to the
point of tangency is perpendicular to the tangent.
C. An arc f a given radius tangent to two
lines at right angles.
D. The point of intersection is the
radius.
A geographic map shows the following
details except____
A. boundaries of countries
B. important towns
C. ground surfaces
D. roads rivers and lakes
What kind of triangle has two equal sides
and two equal angles.
A. obtuse
B. equilateral
C. isosceles
D. scalene
What usually is used by a draftsman to
make the pencil point sharp ?
A. Blade
B. Pad of sandpaper
C. Pencil sharpener
D. Sharp knife
What can you use to scrape off incorrectly
inked line when eraser is nt available?
A. art gum
B. razor blade
C. rubber eraser
D. sharpener
When using lower case letter, how many
horizontal guidelines are used ?
A. 3
B. 4
C. 5
D. 6
A drawing that represents the three
exploded views of an object. The most common views are front, to and right side
view. What do you call this drawing?
A. Cavalier Drawing
B. Isometric drawing
C. Orthographic Drawing
D. Perspective Drawing
What line used to represent the hidden
side of the object drawn
A. . Center Line
B. Ditto line
C. Invisible line
D. Object Line
It is a hand-operated device in a water
circuit connection that is used to control the flow of water in a piping
system.
a. flanged
b. valve
c. union joint
d. universal joint
Manufactures of water supply materials
make use of bronze, brass, gunmetal, steel, cast iron, glass or plastics or a
combination because of it characteristics that it is
a. high resistance to water
b. high corrosive to water
c. high corrosive resistance to water
d. high value to water
A drainage fixture designed to prevent
potentially dangerous sewer gases from entering the house. It is attached to
the roofing of the house.
a. joint
b. fixture
c. venting pipe
d. traps
A type of materials use in plumbing system
that offers possibly the greatest range of screwed plastics fittings well
suited to domestic, commercial and industrial applications.
a. uPVC system
b. cast iron pipes system
c. metal and plastic system
d. stainless pipes system
A type of pipe made of concrete and
usually use for sewer purpose due to large diameter in size and durability. It
has the ability to adopt soil environment with no danger of rusting
a. soil pipes
b. sewer pipe
c. water pipes
d. drainage pip
What particular tool will be use to by
plumber when tightening or loosen pipe fitting
a. adjustable wrench
b. pipe wrench
c. pliers
d. basin wrench
A building has a system of pipes and
drains installed for the purpose of distribution of potable drinking water and
the removal of waterborne wastes
a. Venting system
b. Water system
c. Drainage system
d. Plumbing system
Employees are separated involuntarily due
to _______.
a.Low pay
b.Declining sales
c. poor working condition
d. lure of high paying jobs
aWho exposed on the Theory of Bureaucratic
Management?
a.Max Webber
b.Mary Parker Follett
c.Chester Barnard
d.Lillian Gilbreth
Good public relation presupposes good
internal _________.
a.Reaction
b.Communication
c.attitude
d.response
What is meant by P.O?
a.Purchase Option
b.Product Order
c. Production Office
d. Purchase Order
Which is the 30-ton room-sized computer
with over 18,000 vacuum tubes build by John Mauchly and Eckert?
a. MITS Altair 800
b. UNIVAC
c. ENIAC
d. Colossus
Who introduced the concept of providing
ALU in the computer system?
a. Joseph Marie Jacquard
b. Charles Babbage
c. John Von Newman
d. Herman Hollerith
Which as the raw material to be processed
by the computer?
a. Information
b. Data
c. Graphics
d. Objects
What is meant to put information into the
computer?
a. Launch
b. File
c. Install
d. Input
Which allows it use to upload and download
files from other computers for the net?
a. Usenet
b. Search engine
c. Telnet
d. File transfer protocol
Which of the following makes a window as
small as it can get?
a. Maximize
b. Save
c. Restore
d. Minimize
The drainpipes connections are lead away
from all fixtures at a certain calculated slope of
a. ½ per ft
b. 5/8 per ft
c. 1/8 per ft
d. ¼ per ft 18
Today’s modern plumbing makes use of
central fitting suitable for joining both imperial and metric sizes of medium
and high density polyethylene pipe. This type of fitting is made of
a. nylon material
b. fiber
c. plastics
d. syntactic
This type of material is use for making
flanged. The color is gray and it is usually hard but brittle and not affected
much by massive rusting when expose to air and water.
a. Steel
b. Mild steel
c. cast iron
d. stainless steel
An activity concerned with obtaining the
right kind of goods in the right amount, at the right time, at the right price
and, from the right source.
a.Purchasing
b.buying
c.retailing
d.selling
Margin of difference between cost price
and selling price.
a.selling price
c.c.o.d.
c.mark-down
d.mark-up
Checking the quantity and quality of
merchandise purchased.
a.mark-up
b.purchasing
c.receiving
d.price
An activity concerned with obtaining food
of the right kind, at the right price from the right source.
a.mark-up
b.purchasing
b.receiving
d.price
Requires wise purchasing, vigilant
checking, proper storage of goods, and reasonable pricing.
a.wholesaling
b.purchasing
c.pricing
d.retailing
This sales type requires the customers to
pay for cash for the goods he/she buys and store delivers the goods to his/her
home.
a.Cash-Send or Cash Deliver Sale
b.Charge-Send or Charge-Deliver
c.Cash-Take-Sale
d.Charge-Take-Sale
The customer pays for the goods and takes
these homes with him/her.
a.Cash-Send or Cash Deliver Sale
b.Charge-Send or Charge-Deliver
c.Cash-Take-Sale
d.Charge-Take-Sale
The goods are charged to the customer and
then deliver to his/her home.
a.Charge-Send or Charge-Deliver
b.Cash-Send or Cash Deliver Sale
c.Cash-Take-Sale
d.Charge-Take-Sale
This type of sale requires the customer to
order a merchandise and request the store to lay-it away until he/she calls for
it at the near future. The customer makes a deposit, and the store agrees to
hold the merchandise for a specified period of time.
a.Part-Cash-Part Charge Sale
b.Installment Sale
c.C.O.D. Sale
d.Lay-Away or Will-Call Sale
A part of the amount of the merchandise is
paid in cash by the customer, and the rest of the amount is charged to his/her
account.
a.Part-Cash-Part Charge Sale
b.Installment Sale
c.C.O.D. Sale
d.Lay-Away or Will-Call Sale